Sanitary Pipe Fittings Union | Chuanglan Valve

▲

Sanitary Pipe Fittings & Union | Tri-Clamp Weld

Sanitary unions that seal without gaskets degrading — 3-A compliant.

Complete hygienic skid fitting range - 90/45 elbow, tee, reducer, cap, cross, SMS/ISO union in SS304 / SS316L. Internal polish Ra≤0.8µm (optional 0.5µm), Tri-Clamp / butt-weld / male-female ends, food-grade EPDM / Silicone / PTFE gaskets. DIN 11850 / ISO / SMS standards.

OEM/ODMCustom Manufacturing
ISO 9001:2015Quality Management
Established 2009Valve Manufacturing
7–15 DaysLead Time

* Standard lead time depends on order quantity and destination country. 5–10 days to Southeast Asia, 15–20 days to the Middle East.

✍️ Reviewed by Chuanglan Valve Engineering Team · Last updated Oct 2026 · Follow us on LinkedIn
Sanitary pipe fittings tri-clamp elbow tee reducer union SS316L 3A - Chuanglan Valve

Sanitary pipe fittings and unions cover the complete hygienic skid - elbows, tees, reducers, caps, crosses and SMS/ISO unions - all polished SS316L with internal finish Ra≤0.8µm. Built for food, beverage, dairy, brewery, pharma and personal-care process lines where food-grade hygiene compliance and CIP/SIP compatibility are required.

Our sanitary pipe fittings come in sizes 1″4″ (DN25–DN100), SS304 / SS316L. Tri-Clamp (3A), butt-weld or male/female union ends. Internal polish Ra≤0.8µm (optional 0.5µm), external bead-blasted. food-grade EPDM, Silicone or PTFE gaskets. Standard 3A / DIN 11850 / ISO / SMS dimensions. We also supply matching sanitary ball valves, check valves, clamps and gaskets in one container.

Every fitting is verified by roughness tester, caliper and visual inspection before shipment. Tri-Clamp ends allow quick disassembly for CIP inspection; butt-weld ends provide zero external crevice for permanent skids; SMS/ISO unions allow serviceable joints without rotating the pipe. Send us your BOM and we will quote the full skid package.

🌏 Southeast Asia & Middle East Market Notes

Indonesia / Malaysia dairy & palm oil: 1.5″2″ SS316L Tri-Clamp elbows and tees for milk receivers and CIP return - 316L mandatory because palm oil CIP uses hot caustic + nitric acid daily.

Thailand / Vietnam brewery: 2″3″ eccentric reducers on horizontal pump suction lines (flat side up) + SMS unions for sampling points. Ra ≤ 0.5 µm electropolished on bright beer lines.

Saudi Arabia / UAE pharma & bottled water: 1″2″ butt-weld tees and elbows for WFI loops. Sanitary audit requires 3.1 MTR per heat, Ra ≤ 0.4 µm electropolish, EHEDG cleanability declaration.

Sizing a new hygienic skid? Send your P&ID or fitting list - we will quote valves + fittings + clamps + gaskets as one BOM.

Get Free BOM Take-Off →

Fitting Type Comparison - Which One Do You Need?

FittingFunctionCommon UseEnd Type
90° ElbowChange direction 90°Skid routing, pump dischargeTri-Clamp / weld
45° ElbowChange direction 45° (gentler)Low-shear lines, pump suctionTri-Clamp / weld
TeeBranch flow into / out of main lineSampling, CIP connection, tank inletTri-Clamp / weld
Concentric ReducerReduce size straight (centerline aligned)Vertical lines, general processTri-Clamp / weld
Eccentric ReducerReduce size (flat side flat)Horizontal pump suction - prevent air pocketTri-Clamp / weld
CapBlank off dead endTank nozzle, future expansionTri-Clamp / weld
Cross4-way branchingCIP header, utility manifoldTri-Clamp / weld
SMS / ISO UnionServiceable mechanical jointSampling point, instrument, pump flangeMale/female threaded

Technical Specifications

Size Range1″ - 4″ (DN25 - DN100); 6″+ on request
Fitting Types90° / 45° elbow, tee, concentric/eccentric reducer, cap, cross, SMS/ISO union
End ConnectionTri-Clamp (3A), butt-weld, male/female union
Body MaterialSS316L (1.4404) standard; SS304 (1.4301) option for cost-sensitive water-based lines
Internal PolishRa ≤ 0.8 µm standard; Ra ≤ 0.5 µm / 0.4 µm electropolish optional
External FinishBead-blasted
GasketEPDM / Silicone / PTFE (21 CFR 177)
Pressure RatingPN10 / 10 bar (at 20°C)
Temperature Range-196°C ~ +200°C (gasket dependent)
Inspectionfull visual and dimensional inspection per EN 10204
Material CertificatesEN 10204 3.1 MTC included (heat number traceable to mill test report)
Standard3A, 21 CFR 177, DIN 11850, ISO, SMS, EHEDG cleanable

Dimension Table - Sanitary Tri-Clamp Fittings (mm)

SizeDN90° Elbow (A)Tee (A)Reducer (L)
1"25505060
1.5"40656575
2"50808090
2.5"659595110
3"80110110130
4"100130130150

* Reference values; contact us for full drawing for your specific fitting type and end standard.

🧮 Worked Example: Indonesian Dairy CIP Skid Fitting BOM

Project: A medium-sized dairy in West Java is building a CIP skid for a pasteurized milk line. Process engineer sends a P&ID and asks us to supply all hygienic fittings. The skid uses 2″ main line, but the CIP return drops to 1.5″ going back to the CIP tank, and there is a 1″ sampling point on the discharge header.

Step 1 - Material: CIP weekly runs 85°C hot caustic (NaOH) + nitric acid rinse. SS304 would pit under nitric acid over 2–3 years. We specify SS316L for all fittings - the 25% price difference is justified by the CIP chemistry, and West Java coastal humidity would attack 304 anyway.

Step 2 - Pump suction reducer: The product pump suction comes from a 2″ tank outlet and reduces to 1.5″ pump flange. This is a horizontal line. If we used a concentric reducer, air would pocket on top and cause vapor lock at the pump. We specify eccentric reducer, flat side up - 2″ × 1.5″, Tri-Clamp both ends.

Step 3 - Sampling point: The 1″ sampling port on the 2″ discharge header must be disassembled daily for lab samples. Tri-Clamp would work, but it is slow. We specify SMS/ISO 1″ male-female union at the tee branch - hand-tighten for daily use, no tools needed.

Step 4 - Polish and gasket: Milk line, 3A audit. Internal polish Ra ≤ 0.5 µm (one step up from standard 0.8). Gaskets EPDM (food-grade, handles 140°C SIP). We include spare EPDM gaskets in the BOM because the customer did not specify them.

Result: 14 fittings total - 6× 90° elbow, 2× tee, 1× eccentric reducer 2″×1.5″, 1× concentric reducer 2″×1″, 2× cap for future expansion, 2× SMS union 1″. All Tri-Clamp except the unions. Shipped with 28 EPDM gaskets + clamps. One container, one MTR.

⚠️ 4 Common Mistakes When Ordering Sanitary Fittings

Mistake 1 - Concentric reducer on horizontal pump suction: Concentric reducers leave an air pocket on top of the pipe. This causes vapor lock, cavitation, and pump failure. For any horizontal suction line, always specify eccentric reducer with flat side up.

Mistake 2 - Using SS304 on aggressive CIP: Nitric acid, chlorine sanitizers and coastal humidity all pit 304 within 2–3 years. If your CIP uses acids or your plant is near the sea (Indonesia, Thailand, Middle East coast), spec SS316L from day one - the upgrade pays for itself in one audit cycle.

Mistake 3 - Forgetting gaskets and clamps in the BOM: Customers often order fittings only and forget that each Tri-Clamp joint needs a gasket + clamp. We always cross-check your BOM and quote the matching gaskets + clamps in the same shipment - otherwise the fittings arrive and nothing can be assembled.

Mistake 4 - Specifying butt-weld on a line that needs inspection: Permanent welds save money on long runs, but you cannot disassemble them for CIP inspection or gasket replacement. For any line that needs periodic teardown (skid connections, sampling, pump flanges), use Tri-Clamp or SMS union - not butt-weld.

📋 Commercial Terms

Payment: T/T 30% deposit + 70% before shipment; L/C at sight accepted for large orders. PayPal for sample orders.

Warranty: 12 months after shipment for material and manufacturing defects - covers casting defects, dimension non-conformance, surface finish non-conformance and weld defects. Damage from misuse, improper CIP chemicals, abrasion beyond spec, or coastal corrosion from failed sealing is not covered.

Packaging: Export plywood case; fumigation-free wooden pallet; each fitting individually wrapped to protect polished surfaces.

Shipping Documents: MTC / EN 10204 3.1 material certificate, packing list, commercial invoice; certificate of origin on request.

Shipment Port: FOB Ningbo / Shanghai, China; CIF / DAP available on request.

Third-Party Inspection: SGS / Bureau Veritas / Intertek pre-shipment inspection supported at buyer cost.

Need Sizing Help or a Quote?

Send size (DN), pressure (PN/ANSI), material (304/316L), seat (EPDM/Viton) and quantity — we reply within 24 hours.

Get Free Quote »

FAQ

Tri-Clamp, butt-weld or union end - which do I specify?

Tri-Clamp for lines that need periodic disassembly (CIP inspection, gasket replacement, skid transport) - the hygienic default. Butt-weld for permanent welded skids with zero external crevice (pharma WFI / high-purity). SMS/ISO male-female union for serviceable joints where the pipe cannot rotate - sampling points, instrument connections, pump flanges. Most food & beverage skids mix all three.

SS304 or SS316L - is the upgrade worth it?

SS304 is fine for water-based food, dairy, brewery and personal-care lines. SS316L (with molybdenum) is mandatory for CIP caustic / nitric acid / chlorine sanitizers, seawater, salty brines, pharma WFI, and outdoor / coastal installations. Price difference ~20–30%; if you run aggressive CIP or export to a coastal climate (Middle East / Southeast Asia), spec 316L.

What internal polish (Ra) do I need?

Ra ≤ 0.8 µm is the 3A food & beverage standard - handles CIP/SIP, no product buildup. Ra ≤ 0.5 µm for dairy, brewery and pharma production where visual verification and low biofilm adhesion matter. Ra ≤ 0.4 µm (electropolished) for WFI / pure steam / pharma high-purity. Tell us your audit level (3A / EHEDG / cGMP) and we match.

Which gasket material - EPDM, Silicone or PTFE?

EPDM is the hygienic default - water-based media, CIP caustic / nitric acid, SIP steam to ~140°C. Silicone for ultra-high-temp SIP (~200°C) and oily / fatty media. PTFE for aggressive solvents, dairy CIP acids and extreme chemical resistance. All gaskets meet 21 CFR 177 requirements.

Concentric or eccentric reducer - which is right?

Concentric reducer for vertical lines and general process piping - centerline stays straight. Eccentric reducer (flat side up) for horizontal pump suction lines - prevents air pockets / vapor lock at the pump inlet. Always specify eccentric with flat side up for pump suction.

Do you supply clamps and gaskets together with fittings?

Yes. Every Tri-Clamp fitting order ships with matching EPDM gaskets and heavy-duty stainless clamps by default. If you need Silicone / PTFE gaskets or single-pin / double-pin clamps, tell us in the BOM. We also supply sanitary ball valves and check valves so the whole skid arrives in one container.

MOQ, stock and lead time?

MOQ is 1 piece. Common sizes (1″2″ SS304 / SS316L Tri-Clamp elbows, tees, reducers) are usually in stock (5–7 days). Unusual sizes, eccentric reducers, caps, crosses, SMS/ISO unions, butt-weld ends, Ra ≤ 0.4 µm finish, or mixed-type packing lists take 7–15 days. Send us your BOM and we quote one container.

What is your warranty period?

We provide a 12-month warranty after shipment for material and manufacturing defects. This covers casting defects, dimensional non-conformance, surface finish non-conformance and weld defects. Damage from misuse, improper CIP chemicals, abrasive media beyond specified limits, or field modifications is not covered. Always provide the heat number from the EN 10204 3.1 MTC when raising a warranty claim.

📚 Further reading:
• Butterfly Valve Selection Guide (Size, Pressure, Material)
• How to Select a Wafer Butterfly Valve for Seawater Service
• Wafer Check Valve vs Swing Check Valve (2026 Guide)

You May Also Need

Request a Quote for This Sanitary Pipe Fittings & Union

Tell us the size, pressure and quantity you need. We reply within one working day.








    Need a Custom Valve or Fitting?

    Send us your specs: pressure, size, material and quantity. Our team will review the requirements and provide a direct quote.

    Southeast Asia: Indonesia, Malaysia, Thailand, Vietnam, Singapore, Philippines · Middle East: Saudi Arabia, UAE, Qatar, Kuwait, Oman, Bahrain · Other: the Americas, Europe, Africa, Australia

    FOB Ningbo / Shanghai · We usually reply within 24 business hours.

    Commercial terms: T/T 30% deposit + 70% before shipment, L/C at sight may be considered · export plywood case · 12 months warranty after shipment · EN 10204 3.1 MTC available on request · third-party inspection can be arranged on request.

    Disclaimer: This guide is for general engineering reference only. Final valve selection, sizing and installation must follow the manufacturer data sheet, the project P&ID and the applicable code (EN 1092, ASME B16.5, ASME B16.34, EN 10204 3.1). Where this article and those documents differ, the documents govern.