Pneumatic Sanitary Butterfly Valve | Chuanglan Valve

▲

Pneumatic Sanitary Butterfly Valve | Tri-Clamp

Clean-grade automated valves for continuous CIP production lines.

food-grade automated hygienic butterfly valve — SS316L body Ra≤0.8μm, mirror-polished disc, food-grade EPDM / Silicone / PTFE seat, DA or SR rack-and-pinion actuator, NAMUR solenoid / limit switch / positioner ready for PLC/SCADA integration.

OEM/ODMCustom Manufacturing
ISO 9001:2015Quality Management
Established 2009Valve Manufacturing
7–15 DaysLead Time

* Standard lead time depends on order quantity and destination country. 5–10 days to Southeast Asia, 15–20 days to the Middle East.

✍️ Reviewed by Chuanglan Valve Engineering Team · Last updated Oct 2026 · Follow us on LinkedIn
Pneumatic sanitary butterfly valve tri-clamp SS316L actuator food-grade - Chuanglan Valve

A pneumatic sanitary butterfly valve pairs a 3A-compliant hygienic butterfly body with an aluminum rack-and-pinion actuator — the go-to automated control valve for food, beverage, dairy, brewery, pharma and personal-care CIP/SIP lines where cleanability, low dead space and PLC/SCADA integration are mandatory.

Our pneumatic sanitary butterfly valve is available in sizes 1″–4″ (DN25–DN100), SS316L body with internal polish Ra≤0.8μm, mirror-polished disc. food-grade EPDM, Silicone or PTFE seats. Tri-Clamp ends (3A), butt-weld optional. Double-acting or spring-return fail-close actuator, 5–7 bar air supply. NAMUR solenoid, limit switch box and positioner available. For manual operation see sanitary butterfly valve; for tight shutoff see pneumatic sanitary ball valve. get a detailed quotation with seal and actuator action (DA/SR).

Every valve is shell + seat pressure tested plus actuator stroke tested before shipment. The rack-and-pinion actuator provides fast, reliable 90° on/off or modulating operation — ideal for CIP/SIP cycles and automated production lines. Because the butterfly disc passes through the media, pressure drop is very low — this is why butterfly valves dominate large-line (≥2″) bulk transfer. Where bubble-tight shutoff is needed, pair the butterfly with a ball valve downstream. We directly serve EPC contractors and valve distributors in Southeast Asia (Indonesia, Malaysia, Thailand, Vietnam) and the Middle East (Saudi Arabia, UAE, Qatar, Kuwait).

Southeast Asia & Middle East Market Notes

Thailand / Vietnam breweries: 3″–4″ DA pneumatic butterfly valves on wort / beer bulk transfer lines, positioner (4–20 mA) for flow control. EPDM seat handles hot wort up to 95°C.

Indonesia / Malaysia dairy & beverage: 2″–3″ SR fail-close valves on CIP return header, NAMUR solenoid + limit switch. PLC closes automatically on CIP cycle.

Saudi Arabia / UAE bottled water & pharma: 2″–4″ DA valves on bottle filler bypass loops, 3A / EHEDG cleanability declaration for Sanitary audit.

Building a brewery / dairy CIP skid? We supply matched automated butterfly + ball + check valves pre-wired, air-tested, with one MTR.

Get Free Skid Take-Off →

Pneumatic Sanitary Butterfly vs Ball vs Diaphragm vs Check Comparison

Valve TypeBest ForPressure DropShutoffCost (auto.)
Pneumatic ButterflyLarge lines, bulk transfer, CIP supply / return, flow controlVery low (disc in flow)Weeps after cyclesBaseline
Pneumatic BallTight shutoff, tank outlet, product isolationFull-bore but ball pocketBubble-tight per API 598~1.6× butterfly
Pneumatic DiaphragmPharma WFI, aggressive CIP chemicalsLowZero dead space~2.5× butterfly
Pneumatic CheckBackflow prevention, CIP returnMedium (clack disc)~0.6× butterfly
Manual Butterfly (no actuator)Rarely-opened isolation, sampling~0.3× automated

Technical Specifications

Size Range1″ - 4″ (DN25 - DN100); 6″+ on request
End ConnectionTri-Clamp (3A standard), butt-weld / weld-on hub optional
Body MaterialSS316L (1.4404) investment casting, internal Ra ≤ 0.8 μm
DiscSS316L mirror polished
SeatEPDM / Silicone / PTFE (21 CFR 177)
ActuatorAluminum rack & pinion, double-acting (DA) or spring-return (SR / FC)
Air Supply5 – 7 bar (dry, filtered, lubrication-free)
Pressure RatingPN10 / 10 bar (at 20°C)
Temperature Range-10°C ~ +140°C EPDM; +180°C PTFE; +200°C Silicone
AccessoriesNAMUR solenoid (24 VDC), ITS-100 limit switch box, 4–20 mA positioner
Testingshell + seat pressure test + actuator stroke test per API 598
Material CertificatesEN 10204 3.1 MTC (material test reports) included
Standard3A, 21 CFR 177, ISO, DIN 11850, EHEDG cleanable

Dimension Table — Pneumatic Sanitary Butterfly Valve (mm)

SizeDNL (Face-to-Face)H (Total Height with Actuator)
1"2551195
1.5"4064215
2"5064225
2.5"6576245
3"8076255
4"100102285

* Dimensions may vary by actuator size (DA vs SR); contact us for complete drawing with solenoid / positioner mounted.

Worked Example: 3″ Automated Butterfly on a Bangkok Brewery Wort Line

Project: Brewery wort transfer from lauter tun to whirlpool. 3″ (DN80) sanitary butterfly valve. Need modulating control — flow must ramp from 20% to 80% over 10 minutes as the tun drains. CIP cycle hits 2% NaOH at 85°C weekly.

Step 1 — Why butterfly, not ball? 3″ line, bulk transfer, low pressure drop matters. A ball valve at 3″ costs 1.6× the butterfly and has a higher pressure drop through the ball pocket. The butterfly's short face-to-face (76 mm) also saves space on the skid. For bulk transfer, butterfly is the correct choice.

Step 2 — Why DA + positioner, not SR? This is modulating duty. A spring-return positioner would be too stiff for continuous throttling (spring fights the positioner). Double-acting with a 4–20 mA positioner gives smooth 20–80% flow control. Air supply is reliable (dedicated brewery compressor), so fail-close isn't required — the wort line isn't a sterile barrier.

Step 3 — Seat: CIP weekly hits 85°C NaOH. EPDM seat — good to 140°C, handles caustic, elastic, low torque. PTFE would be overkill and require an oversized actuator. Silicone would be too soft for long-term throttling.

Step 4 — Skid package: Valve + DA actuator + positioner (4–20 mA) + FRL air preparation. Pre-assembled, pre-wired with M12 connector, air-tested. Brewery PLC reads the 4–20 mA signal and ramps flow as the tun drains — no manual operator needed.

4 Common Mistakes When Ordering Automated Sanitary Butterfly Valves

Mistake 1 — Using butterfly for tight shutoff: Butterfly valves weep at tank bottom and product isolation after 100+ cycles. Always pair butterfly (bulk transfer) with a ball valve (tight shutoff) downstream. Don't use butterfly where zero leak is required.

Mistake 2 — Under-sizing the actuator on PTFE seat: PTFE seat has much higher break torque than EPDM. A standard actuator that works fine on EPDM will stall on PTFE. When switching seat material, always ask us to re-size the actuator — don't assume the same frame works.

Mistake 3 — Specifying SR on a modulating line: Spring-return actuators with positioners are stiff and wear out fast in continuous throttling. For flow control, always use double-acting + positioner. Save SR for on/off fail-close safety duty.

Mistake 4 — Skipping the FRL air preparation: Wet, oily, unfiltered air destroys rack-and-pinion actuators in 6 months. Install a 5 μm filter-regulator-lubricator within 2 m of the actuator. Dry instrument air at 5–7 bar doubles actuator life.

Commercial Terms & Shipping

Payment: T/T 30% deposit + 70% before shipment; L/C at sight accepted for orders above USD 20,000. PayPal for sample orders.

Warranty: 12 months after shipment for material and manufacturing defects. Covers casting defects, seat leakage, disc surface finish non-conformance, actuator stroke failure and solenoid non-conformance. Damage from misuse, improper CIP chemicals, abrasive media beyond specified limits, or lack of air filtration is not covered.

Packaging: Export plywood case (fumigation-free). Each valve packed in individual plastic bag with Tri-Clamp end caps and actuator protected in foam to prevent transit damage.

Shipping Documents: EN 10204 3.1 MTC, 3-A compliance declaration on request, food-grade seat certificate, pressure test report, actuator stroke test report, packing list, commercial invoice. Certificate of origin available on request.

Shipment Port: FOB Ningbo / Shanghai, China. Can also arrange CIF / DAP to your destination port.

Third-Party Inspection: SGS, Bureau Veritas or Intertek pre-shipment inspection supported at your cost.

Need Sizing Help or a Quote?

Send size (DN), pressure (PN/ANSI), material (304/316L), seat (EPDM/Viton) and quantity — we reply within 24 hours.

Get Free Quote »

FAQ

Double-acting (DA) or spring-return (SR) — which actuator?

DA for normal CIP/SIP on/off automation with reliable air supply — equal torque, lower cost. SR (fail-close / FC) for any line where air loss must close the valve — product tanks, sterile barriers, safety interlocks. For fail-open service we can also supply SR with the spring acting in the opening direction.

EPDM, Silicone or PTFE seat — which is right?

EPDM is the industry default for water-based food & beverage, CIP caustic / nitric acid, and SIP steam up to ~140°C. Silicone for ultra-high-temp SIP (~200°C) and oily / fatty media. PTFE for aggressive solvents and dairy CIP acids — but higher torque, so actuator must be oversized. All seats meet 21 CFR 177 requirements.

What accessories do I need for PLC integration?

Minimum = 5/2-way NAMUR solenoid (24 VDC). For position feedback add a limit switch box (inductive proximity). For modulating / flow control add a pneumatic positioner with 4–20 mA input. We pre-assemble, pre-wire with M12, and air-test before shipment.

Tri-Clamp or butt-weld end?

Tri-Clamp is the hygienic default — tool-free disassembly for seat replacement, CIP inspection. Butt-weld for permanent welded skids in pharma WFI. Most breweries / dairies choose Tri-Clamp.

Is this valve truly CIP/SIP cleanable? Any dead leg?

Yes. Single-piece investment cast body, no internal crevice, wetted surfaces Ra ≤ 0.8 μm electro-polished. For pharma high-purity we can supply Ra ≤ 0.4 μm and a 3-A / EHEDG declaration of cleanability.

Can I upgrade from manual to pneumatic later?

Yes — every sanitary butterfly valve shares a standard ISO 5211 top flange. Start with manual lever, bolt on a rack-and-pinion actuator in 10 minutes without replacing the body. We sell the actuator as a retro-fit kit with mounting bracket and solenoid.

MOQ, stock and lead time?

MOQ is 1 piece. 1″–2″ EPDM DA valves are usually in stock (7–15 days). 3″–4″, Silicone / PTFE, SR fail-close, pre-assembled solenoid / positioner, butt-weld, or Ra ≤ 0.4 μm finish takes 15–30 days. We ship together with manual sanitary butterfly, sanitary ball, gaskets and clamps in one container.

What is the warranty period for your valves?

We provide a 12-month warranty after shipment for material and manufacturing defects. This covers casting defects, seat leakage, disc surface finish non-conformance, actuator stroke failure and solenoid non-conformance. Damage from misuse, improper CIP chemicals, abrasive media beyond specified limits, or lack of air filtration is not covered.

📚 Further reading:
• Butterfly Valve Selection Guide (Size, Pressure, Material)
• How to Select a Wafer Butterfly Valve for Seawater Service
• Wafer Check Valve vs Swing Check Valve (2026 Guide)

You May Also Need

Request a Quote for This Pneumatic Sanitary Butterfly Valve

Tell us the size, pressure and quantity you need. We reply within one working day.








    Need a Custom Valve or Fitting?

    Send us your specs: pressure, size, material and quantity. Our team will review the requirements and provide a direct quote.

    Southeast Asia: Indonesia, Malaysia, Thailand, Vietnam, Singapore, Philippines · Middle East: Saudi Arabia, UAE, Qatar, Kuwait, Oman, Bahrain · Other: the Americas, Europe, Africa, Australia

    FOB Ningbo / Shanghai · We usually reply within 24 business hours.

    Commercial terms: T/T 30% deposit + 70% before shipment, L/C at sight may be considered · export plywood case · 12 months warranty after shipment · EN 10204 3.1 MTC available on request · third-party inspection can be arranged on request.

    Disclaimer: This guide is for general engineering reference only. Final valve selection, sizing and installation must follow the manufacturer data sheet, the project P&ID and the applicable code (EN 1092, ASME B16.5, ASME B16.34, EN 10204 3.1). Where this article and those documents differ, the documents govern.