
A pneumatic sanitary butterfly valve pairs a 3A-compliant hygienic butterfly body with an aluminum rack-and-pinion actuator — the go-to automated control valve for food, beverage, dairy, brewery, pharma and personal-care CIP/SIP lines where cleanability, low dead space and PLC/SCADA integration are mandatory.
Our pneumatic sanitary butterfly valve is available in sizes 1″–4″ (DN25–DN100), SS316L body with internal polish Ra≤0.8μm, mirror-polished disc. food-grade EPDM, Silicone or PTFE seats. Tri-Clamp ends (3A), butt-weld optional. Double-acting or spring-return fail-close actuator, 5–7 bar air supply. NAMUR solenoid, limit switch box and positioner available. For manual operation see sanitary butterfly valve; for tight shutoff see pneumatic sanitary ball valve. get a detailed quotation with seal and actuator action (DA/SR).
Every valve is shell + seat pressure tested plus actuator stroke tested before shipment. The rack-and-pinion actuator provides fast, reliable 90° on/off or modulating operation — ideal for CIP/SIP cycles and automated production lines. Because the butterfly disc passes through the media, pressure drop is very low — this is why butterfly valves dominate large-line (≥2″) bulk transfer. Where bubble-tight shutoff is needed, pair the butterfly with a ball valve downstream. We directly serve EPC contractors and valve distributors in Southeast Asia (Indonesia, Malaysia, Thailand, Vietnam) and the Middle East (Saudi Arabia, UAE, Qatar, Kuwait).
Southeast Asia & Middle East Market Notes
Thailand / Vietnam breweries: 3″–4″ DA pneumatic butterfly valves on wort / beer bulk transfer lines, positioner (4–20 mA) for flow control. EPDM seat handles hot wort up to 95°C.
Indonesia / Malaysia dairy & beverage: 2″–3″ SR fail-close valves on CIP return header, NAMUR solenoid + limit switch. PLC closes automatically on CIP cycle.
Saudi Arabia / UAE bottled water & pharma: 2″–4″ DA valves on bottle filler bypass loops, 3A / EHEDG cleanability declaration for Sanitary audit.
Building a brewery / dairy CIP skid? We supply matched automated butterfly + ball + check valves pre-wired, air-tested, with one MTR.
Get Free Skid Take-Off →Pneumatic Sanitary Butterfly vs Ball vs Diaphragm vs Check Comparison
| Valve Type | Best For | Pressure Drop | Shutoff | Cost (auto.) |
|---|---|---|---|---|
| Pneumatic Butterfly | Large lines, bulk transfer, CIP supply / return, flow control | Very low (disc in flow) | Weeps after cycles | Baseline |
| Pneumatic Ball | Tight shutoff, tank outlet, product isolation | Full-bore but ball pocket | Bubble-tight per API 598 | ~1.6× butterfly |
| Pneumatic Diaphragm | Pharma WFI, aggressive CIP chemicals | Low | Zero dead space | ~2.5× butterfly |
| Pneumatic Check | Backflow prevention, CIP return | Medium (clack disc) | ~0.6× butterfly | |
| Manual Butterfly (no actuator) | Rarely-opened isolation, sampling | ~0.3× automated |
Technical Specifications
| Size Range | 1″ - 4″ (DN25 - DN100); 6″+ on request |
| End Connection | Tri-Clamp (3A standard), butt-weld / weld-on hub optional |
| Body Material | SS316L (1.4404) investment casting, internal Ra ≤ 0.8 μm |
| Disc | SS316L mirror polished |
| Seat | EPDM / Silicone / PTFE (21 CFR 177) |
| Actuator | Aluminum rack & pinion, double-acting (DA) or spring-return (SR / FC) |
| Air Supply | 5 – 7 bar (dry, filtered, lubrication-free) |
| Pressure Rating | PN10 / 10 bar (at 20°C) |
| Temperature Range | -10°C ~ +140°C EPDM; +180°C PTFE; +200°C Silicone |
| Accessories | NAMUR solenoid (24 VDC), ITS-100 limit switch box, 4–20 mA positioner |
| Testing | shell + seat pressure test + actuator stroke test per API 598 |
| Material Certificates | EN 10204 3.1 MTC (material test reports) included |
| Standard | 3A, 21 CFR 177, ISO, DIN 11850, EHEDG cleanable |
Dimension Table — Pneumatic Sanitary Butterfly Valve (mm)
| Size | DN | L (Face-to-Face) | H (Total Height with Actuator) |
|---|---|---|---|
| 1" | 25 | 51 | 195 |
| 1.5" | 40 | 64 | 215 |
| 2" | 50 | 64 | 225 |
| 2.5" | 65 | 76 | 245 |
| 3" | 80 | 76 | 255 |
| 4" | 100 | 102 | 285 |
* Dimensions may vary by actuator size (DA vs SR); contact us for complete drawing with solenoid / positioner mounted.
Worked Example: 3″ Automated Butterfly on a Bangkok Brewery Wort Line
Project: Brewery wort transfer from lauter tun to whirlpool. 3″ (DN80) sanitary butterfly valve. Need modulating control — flow must ramp from 20% to 80% over 10 minutes as the tun drains. CIP cycle hits 2% NaOH at 85°C weekly.
Step 1 — Why butterfly, not ball? 3″ line, bulk transfer, low pressure drop matters. A ball valve at 3″ costs 1.6× the butterfly and has a higher pressure drop through the ball pocket. The butterfly's short face-to-face (76 mm) also saves space on the skid. For bulk transfer, butterfly is the correct choice.
Step 2 — Why DA + positioner, not SR? This is modulating duty. A spring-return positioner would be too stiff for continuous throttling (spring fights the positioner). Double-acting with a 4–20 mA positioner gives smooth 20–80% flow control. Air supply is reliable (dedicated brewery compressor), so fail-close isn't required — the wort line isn't a sterile barrier.
Step 3 — Seat: CIP weekly hits 85°C NaOH. EPDM seat — good to 140°C, handles caustic, elastic, low torque. PTFE would be overkill and require an oversized actuator. Silicone would be too soft for long-term throttling.
Step 4 — Skid package: Valve + DA actuator + positioner (4–20 mA) + FRL air preparation. Pre-assembled, pre-wired with M12 connector, air-tested. Brewery PLC reads the 4–20 mA signal and ramps flow as the tun drains — no manual operator needed.
4 Common Mistakes When Ordering Automated Sanitary Butterfly Valves
Mistake 1 — Using butterfly for tight shutoff: Butterfly valves weep at tank bottom and product isolation after 100+ cycles. Always pair butterfly (bulk transfer) with a ball valve (tight shutoff) downstream. Don't use butterfly where zero leak is required.
Mistake 2 — Under-sizing the actuator on PTFE seat: PTFE seat has much higher break torque than EPDM. A standard actuator that works fine on EPDM will stall on PTFE. When switching seat material, always ask us to re-size the actuator — don't assume the same frame works.
Mistake 3 — Specifying SR on a modulating line: Spring-return actuators with positioners are stiff and wear out fast in continuous throttling. For flow control, always use double-acting + positioner. Save SR for on/off fail-close safety duty.
Mistake 4 — Skipping the FRL air preparation: Wet, oily, unfiltered air destroys rack-and-pinion actuators in 6 months. Install a 5 μm filter-regulator-lubricator within 2 m of the actuator. Dry instrument air at 5–7 bar doubles actuator life.
Commercial Terms & Shipping
Payment: T/T 30% deposit + 70% before shipment; L/C at sight accepted for orders above USD 20,000. PayPal for sample orders.
Warranty: 12 months after shipment for material and manufacturing defects. Covers casting defects, seat leakage, disc surface finish non-conformance, actuator stroke failure and solenoid non-conformance. Damage from misuse, improper CIP chemicals, abrasive media beyond specified limits, or lack of air filtration is not covered.
Packaging: Export plywood case (fumigation-free). Each valve packed in individual plastic bag with Tri-Clamp end caps and actuator protected in foam to prevent transit damage.
Shipping Documents: EN 10204 3.1 MTC, 3-A compliance declaration on request, food-grade seat certificate, pressure test report, actuator stroke test report, packing list, commercial invoice. Certificate of origin available on request.
Shipment Port: FOB Ningbo / Shanghai, China. Can also arrange CIF / DAP to your destination port.
Third-Party Inspection: SGS, Bureau Veritas or Intertek pre-shipment inspection supported at your cost.
Need Sizing Help or a Quote?
Send size (DN), pressure (PN/ANSI), material (304/316L), seat (EPDM/Viton) and quantity — we reply within 24 hours.
Get Free Quote »FAQ
Double-acting (DA) or spring-return (SR) — which actuator?
DA for normal CIP/SIP on/off automation with reliable air supply — equal torque, lower cost. SR (fail-close / FC) for any line where air loss must close the valve — product tanks, sterile barriers, safety interlocks. For fail-open service we can also supply SR with the spring acting in the opening direction.
EPDM, Silicone or PTFE seat — which is right?
EPDM is the industry default for water-based food & beverage, CIP caustic / nitric acid, and SIP steam up to ~140°C. Silicone for ultra-high-temp SIP (~200°C) and oily / fatty media. PTFE for aggressive solvents and dairy CIP acids — but higher torque, so actuator must be oversized. All seats meet 21 CFR 177 requirements.
What accessories do I need for PLC integration?
Minimum = 5/2-way NAMUR solenoid (24 VDC). For position feedback add a limit switch box (inductive proximity). For modulating / flow control add a pneumatic positioner with 4–20 mA input. We pre-assemble, pre-wire with M12, and air-test before shipment.
Tri-Clamp or butt-weld end?
Tri-Clamp is the hygienic default — tool-free disassembly for seat replacement, CIP inspection. Butt-weld for permanent welded skids in pharma WFI. Most breweries / dairies choose Tri-Clamp.
Is this valve truly CIP/SIP cleanable? Any dead leg?
Yes. Single-piece investment cast body, no internal crevice, wetted surfaces Ra ≤ 0.8 μm electro-polished. For pharma high-purity we can supply Ra ≤ 0.4 μm and a 3-A / EHEDG declaration of cleanability.
Can I upgrade from manual to pneumatic later?
Yes — every sanitary butterfly valve shares a standard ISO 5211 top flange. Start with manual lever, bolt on a rack-and-pinion actuator in 10 minutes without replacing the body. We sell the actuator as a retro-fit kit with mounting bracket and solenoid.
MOQ, stock and lead time?
MOQ is 1 piece. 1″–2″ EPDM DA valves are usually in stock (7–15 days). 3″–4″, Silicone / PTFE, SR fail-close, pre-assembled solenoid / positioner, butt-weld, or Ra ≤ 0.4 μm finish takes 15–30 days. We ship together with manual sanitary butterfly, sanitary ball, gaskets and clamps in one container.
What is the warranty period for your valves?
We provide a 12-month warranty after shipment for material and manufacturing defects. This covers casting defects, seat leakage, disc surface finish non-conformance, actuator stroke failure and solenoid non-conformance. Damage from misuse, improper CIP chemicals, abrasive media beyond specified limits, or lack of air filtration is not covered.
📚 Further reading:
• Butterfly Valve Selection Guide (Size, Pressure, Material)
• How to Select a Wafer Butterfly Valve for Seawater Service
• Wafer Check Valve vs Swing Check Valve (2026 Guide)
You May Also Need
Related Technical Guides
Sanitary Butterfly Valve Guide · Pneumatic Actuator Selection · Sanitary Valves for Food & Beverage
Request a Quote for This Pneumatic Sanitary Butterfly Valve
Tell us the size, pressure and quantity you need. We reply within one working day.

