Wafer Knife Gate Valve | Chuanglan Valve

▲

Wafer Knife Gate Valve | Handwheel Chain Wheel

Slurry and sludge eat ordinary valves alive — our knife gates handle abrasion without jamming.

Stainless steel / cast iron wafer knife gate valve, DN50–DN1200, PN6–PN10, for slurry, pulp and viscous media

OEM/ODMCustom Manufacturing
ISO 9001:2015Quality Management
Established 2009Valve Manufacturing
7–15 DaysLead Time

* Standard lead time depends on order quantity and destination country. 5–10 days to Southeast Asia, 15–20 days to the Middle East.

✍️ Reviewed by Chuanglan Valve Engineering Team · Last updated Oct 2026 · Follow us on LinkedIn
Wafer knife gate valve with sharpened stainless steel gate for slurry service - Chuanglan Valve

A wafer knife gate valve uses a sharpened stainless steel gate to cut through viscous, fibrous and slurry media that would jam conventional gate valves. Its thin wafer body fits between two flanges, making it compact and cost-effective for pulp & paper, mining, wastewater treatment, chemical processing and food industry.

We manufacture wafer knife gate valves in stainless steel CF8 (304) and CF8M (316) as our premium range. Cast iron (GG25), ductile iron (GGG40) and WCB carbon steel bodies are available for budget mining and wastewater projects. Sizes DN50–DN1200 (NPS 2″–48″), wafer ends fitting between DIN EN 1092-1 PN6/PN10 / ANSI Class 150 flanges, sharpened SS304/SS316 gate, EPDM/NBR/Viton/PTFE sleeve. Handwheel operator standard; chain wheel for DN300 and above. For automated operation, compare our pneumatic knife gate valve; for clean-water isolation, see our flanged rising stem gate valve.

Every valve is shell and seat pressure tested per API 598 before shipment. MOQ 1 piece, ISO 9001:2015. For general low-cost isolation on clean media, see our wafer butterfly valve. The main advantage of a wafer knife gate valve over a conventional gate valve is its ability to handle slurry, viscous and fibrous media without jamming. The sharpened stainless steel gate slices through pulp, sludge, ore tailings and powder, while the replaceable sleeve provides tight shutoff even with abrasive particles. We directly serve EPC contractors and valve distributors in Southeast Asia (Indonesia, Malaysia, Thailand, Vietnam) and the Middle East (Saudi Arabia, UAE, Qatar, Kuwait).

When selecting a knife gate valve, consider: size (DN50–DN1200), pressure rating (PN6 / PN10 / ANSI 150#), body material (cast iron for raw sewage, ductile iron for slurry, CF8M for chemical/chloride), gate material (SS304 / SS316 sharpened), sleeve material (EPDM / NBR / Viton / PTFE), actuation (handwheel / chain wheel / pneumatic), and flange drilling standard. Always specify the media type and solids concentration — this determines sleeve life and gate hardness.

Southeast Asia & Middle East Market Notes

Indonesia palm oil mills & Malaysia pulp mills: Bleached stock, black liquor and palm oil sludge — CF8M (316) body with Viton sleeve, sharpened SS316 gate. The wafer design saves weight on large DN300–DN600 lines where flanged gate valves would be prohibitively heavy.

Saudi Arabia & UAE mining / phosphate slurry: Ductile iron (GGG40) body with SS316 gate and EPDM sleeve is the standard for phosphate and gypsum tailings. ANSI Class 150 flanges commonly specified.

Vietnam & Thailand wastewater plants: Cast iron (GG25) body with EPDM sleeve, handwheel operated — the most cost-effective choice for raw sewage and sludge lines in municipal treatment plants.

Not sure whether you need knife gate, gate or butterfly valve for your slurry?

Get Free Sizing Report →

Knife Gate vs Conventional Gate vs Butterfly Valve

FeatureKnife Gate ValveConventional Gate ValveButterfly Valve
Best mediaSlurry, pulp, viscous, fibrous, powderClean water, steam, oil, gasClean water, HVAC, air
Pressure ratingPN6-PN10 (low)PN16-PN40 (medium-high)PN10-PN16
Face-to-faceVery short (wafer, ~50–250 mm)Long (EN 558 Series 14)Short (EN 558 Series 20)
Weight (DN300)LightestHeaviestMedium
Stuck on solids?No — sharpened gate cuts throughYes — wedge jams in slurryDisc jams with fibrous stock
Cost (DN300)MediumHighestLowest
Our productKnife Gate ValveFlanged Gate ValveWafer Butterfly Valve

Technical Specifications

TypeWafer knife gate, handwheel / chain wheel operated
Size RangeDN50 – DN1200 (NPS 2″ – 48″)
End ConnectionWafer type, fits between DIN EN 1092-1 PN6/PN10 / ANSI B16.5 Class 150 / JIS 10K flanges
Body MaterialCF8M (316) / CF8 (304) — premium; GGG40 ductile iron / GG25 cast iron / WCB carbon steel on request
GateSS304 / SS316, sharpened edge (optional polished for food)
Sleeve / SeatEPDM / NBR / Viton (FKM) / PTFE
Pressure RatingPN6 – PN10 / ANSI 150#
Temperature Range-10°C ~ +110°C (EPDM) / -20°C ~ +80°C (NBR) / -20°C ~ +180°C (Viton) / -20°C ~ +200°C (PTFE)
ActuationHandwheel (DN50–DN300) / chain wheel (DN300+) / pneumatic (see pneumatic version)
Applicable MediaSlurry, pulp, paper stock, wastewater, ore tailings, powder, syrup, granules
Testingshell & seat pressure test per API 598
Material CertificatesEN 10204 3.1 MTC (material test reports) included
StandardMSS SP-81, API 600, face-to-face per ISO 5752

Dimension Table — DIN EN 1092-1 PN10 Wafer (mm)

L = wafer face-to-face length. Flange OD (D), bolt circle (K) and bolt holes (n-ΦL) below match DIN EN 1092-1 PN10 mating flanges. H (open height) and Do (handwheel diameter) are reference values. ANSI B16.5 Class 150 / JIS 10K drilling available on request.

DNNPSL (mm)Flange OD D (mm)Bolt Circle K (mm)n-ΦLH (mm)Do (mm)
502″501651254-Φ18285180
652½”501851454-Φ18298180
803″502001608-Φ18315220
1004″502201808-Φ18365220
1255″502502108-Φ18400230
1506″602852408-Φ22475280
2008″603402958-Φ22540360
25010″7039535012-Φ22630360
30012″8044540012-Φ22780400
35014″9050546016-Φ22885400
40016″10056551516-Φ26990400
45018″12061556520-Φ261100530
50020″13067062020-Φ261200530
60024″13078072520-Φ301450600
70028″15489584024-Φ301700600
80032″160101595024-Φ332000680
90036″2031115105028-Φ332300680
100040″2161230116028-Φ362500700
120048″2541455138032-Φ362800800

* Standard drilling: DIN EN 1092-1 PN10. For PN6 (lower pressure), flange OD is smaller — contact us for PN6 dimensions. ANSI Class 150 / JIS 10K on request.

Worked Example: Selecting a DN300 Knife Gate Valve for Phosphate Slurry

Project: Isolation valve on a phosphate slurry line at a fertilizer plant in Jubail, Saudi Arabia.
Given: DN300 wafer knife gate valve, phosphate slurry at 15% solids, 40°C, PN10, ANSI Class 150 flanges required.

Step 1 — Confirm valve type:
Phosphate slurry is abrasive and contains crystalline particles. A conventional gate valve wedge would jam within months. A knife gate valve with sharpened SS316 gate slices through the slurry, and the replaceable EPDM sleeve provides tight shutoff.

Step 2 — Select materials:
Body: ductile iron (GGG40) — cost-effective for PN10 slurry service; 316L not required for non-chloride slurry. Gate: SS316 for corrosion resistance. Sleeve: EPDM (15% solids, 40°C). Handwheel operator for manual isolation.

Step 3 — Select flange standard:
End user specified ANSI Class 150. We supply valve with ANSI 150# drilling (NPS 12″, flange OD 285 mm, bolt circle 241 mm, 8×Φ22 bolt holes) — differs from standard DIN PN10 drilling (OD 445 mm, K 400 mm, 12×Φ22). Specify at order time.

Step 4 — Select actuation:
Valve used for maintenance isolation once per month. Handwheel is sufficient. If the line needs automated shutoff for pump protection, upgrade to our pneumatic knife gate valve.

4 Common Mistakes When Selecting Knife Gate Valves

Mistake 1 — Using a knife gate valve for clean water at high pressure: Knife gate valves are PN6-PN10 max. For PN16+ clean water or steam service, use a conventional flanged gate valve — the knife gate sleeve will fail at higher pressure.

Mistake 2 — Wrong sleeve material: EPDM for water/sewage, NBR for oil, Viton for chemical/oil/hot, PTFE for strong acid/alkali. Using EPDM for oil service causes sleeve swelling within weeks.

Mistake 3 — Forgetting sleeve is a wearing part: The sleeve is the primary pressure boundary and will wear out with abrasive slurry. Always keep spare sleeves on site — they are cheap compared to valve replacement.

Mistake 4 — Specifying stainless body for raw sewage: Cast iron (GG25) with EPDM sleeve is the standard for municipal wastewater and costs 40–60% less than CF8M. Use 316L only for food, chemical or chloride service.

Need Sizing Help or a Quote?

Send size (DN), pressure (PN/ANSI), material (304/316L), seat (EPDM/Viton) and quantity — we reply within 24 hours.

Get Free Quote »

Applications

Pulp & Paper: Stock, slurry, black liquor, white liquor, broke handling.
Mining & Minerals: Ore slurry, tailings, ash, phosphate, gypsum, powder.
Wastewater Treatment: Raw sewage, sludge, digested solids, effluent lines.
Chemical & Food: Viscous fluids, granules, syrup, sugar, starch, dairy by-products.

Commercial Terms & Shipping

Payment: T/T 30% deposit + 70% before shipment; L/C at sight accepted for orders above USD 20,000. PayPal for sample orders.

Warranty: 12 months after shipment for material and manufacturing defects. Covers casting defects, sleeve leakage and material non-conformance. Damage from misuse, improper installation, abrasive wear beyond specified limits, or corrosive media not matching the selected sleeve is not covered.

Packaging: Export plywood case (fumigation-free) or seaworthy pallet. Large DN600+ valves on wooden skids. Spare sleeves packed separately.

Shipping Documents: EN 10204 3.1 MTC, pressure test certificate, packing list, commercial invoice. Certificate of origin and BL available on request.

Shipment Port: FOB Ningbo / Shanghai, China. Can also arrange CIF / DAP to your destination port.

Third-Party Inspection: SGS, Bureau Veritas or Intertek pre-shipment inspection supported at your cost.

FAQ

What is the difference between a knife gate valve and a conventional gate valve?

A knife gate valve has a thin, sharpened stainless steel gate that slices through slurry, pulp and viscous media. A conventional gate valve uses a wedge that jams in abrasive or fibrous media. Knife gate = low pressure (PN6-10), short wafer body, slurry service. Conventional gate = higher pressure, long face-to-face, clean media.

What sleeve material should I choose for my application?

EPDM for water, sewage, sludge (up to +110°C). NBR for oil, grease, petroleum. Viton (FKM) for chemicals, hot oil, steam, aromatic solvents. PTFE for strong acid, alkali, aggressive chemical slurry.

Can you supply pneumatic or electric actuated knife gate valves?

Yes. We offer pneumatic cylinder actuated versions for automated slurry lines (common in mines and wastewater plants). Electric actuation is also available on request.

What flange standards do you supply?

Standard drilling is DIN EN 1092-1 PN10. We also drill ANSI B16.5 Class 150, JIS 10K and AS/NZS on request. Specify your required standard when requesting a quote — wafer valve bolt holes must match your pipeline flanges.

Can the sleeve be replaced on site?

Yes. The sleeve is a wearing part and can be replaced without removing the valve from the line — just loosen the bonnet, swap the sleeve, retighten. We supply spare sleeves with every order and as spares.

What is the lead time and MOQ?

MOQ is 1 piece. Standard sizes DN50–DN300 in cast iron / CF8 ship in 15–20 days. Large sizes (DN600+), 316L body or special sleeve materials take 15–30 days.

Do you provide material certificates and pressure test reports?

Yes. Each valve comes with EN 10204 3.1 MTC (material test report), pressure test certificate and ISO 9001:2015 certificate. Third-party inspection (SGS / Bureau Veritas / Intertek) is available on request.

What is the warranty period for your valves?

We provide a 12-month warranty after shipment for material and manufacturing defects. This covers casting defects, sleeve leakage and material non-conformance. Damage from misuse, improper installation or abrasive/corrosive wear beyond specified limits is not covered.

📚 Further reading:
• Butterfly Valve Selection Guide (Size, Pressure, Material)
• Wafer Check Valve vs Swing Check Valve (2026 Guide)
• How to Select a Wafer Butterfly Valve for Seawater Service

You May Also Need

Request a Quote for This Wafer Knife Gate Valve

Tell us the size, pressure and quantity you need. We reply within one working day.








    Need a Custom Valve or Fitting?

    Send us your specs: pressure, size, material and quantity. Our team will review the requirements and provide a direct quote.

    Southeast Asia: Indonesia, Malaysia, Thailand, Vietnam, Singapore, Philippines · Middle East: Saudi Arabia, UAE, Qatar, Kuwait, Oman, Bahrain · Other: the Americas, Europe, Africa, Australia

    FOB Ningbo / Shanghai · We usually reply within 24 business hours.

    Commercial terms: T/T 30% deposit + 70% before shipment, L/C at sight may be considered · export plywood case · 12 months warranty after shipment · EN 10204 3.1 MTC available on request · third-party inspection can be arranged on request.

    Disclaimer: This guide is for general engineering reference only. Final valve selection, sizing and installation must follow the manufacturer data sheet, the project P&ID and the applicable code (EN 1092, ASME B16.5, ASME B16.34, EN 10204 3.1). Where this article and those documents differ, the documents govern.