
A wafer butterfly valve is a quarter-turn shutoff and control valve widely used in HVAC systems, water treatment plants, industrial piping and fire protection. Its thin wafer body fits between two flanges, making it compact, lightweight and cost-effective for large-diameter lines. The disc rotates 90° from open to closed, providing quick shutoff and precise flow control.
We manufacture wafer butterfly valves in stainless steel CF8 (304) and CF8M (316) as our standard product range. Ductile iron (GGG50) and cast iron (GG25) bodies are available for budget HVAC projects where corrosion resistance is not critical. Sizes DN40–DN600 (NPS 1½″–24″), PN10–PN16, ANSI 150#, disc in SS304/SS316 with EPDM/NBR/Viton seat. Lever operator for DN40–DN200; gear operator for DN250 and above.
Every valve is shell and seat pressure tested per API 609 before shipment. MOQ 1 pc, 7–20 days delivery, ISO 9001:2015, shell and seat pressure tested. For automated operation, compare our pneumatic wafer butterfly valve. For food-grade service, see our sanitary butterfly valve. For guidance on selecting the right size and pressure, read our pressure rating reference. get a detailed quotation for your project.
The main advantage of a wafer butterfly valve over a flanged gate valve or ball valve is its compact design and cost-effectiveness, especially for large diameters (DN200 and above). The wafer body is only about 1/3 the face-to-face length of a flanged valve, saving pipe space and weight. EPDM seats provide bubble-tight shutoff for water, air and mild chemicals. When used in pumping stations, pair it with a swing check valve to prevent backflow, and protect equipment with a Y-strainer. Complete the piping system with matching stainless steel flanges.
We directly serve EPC contractors and valve distributors in Southeast Asia (Indonesia, Malaysia, Thailand, Vietnam) and the Middle East (Saudi Arabia, UAE, Qatar, Kuwait).
🌏 Southeast Asia & Middle East Market Notes
Indonesia & Malaysia palm oil mills: High humidity and corrosive condensate — recommend CF8M (316) body with Viton seat for long service life.
Saudi Arabia & UAE desalination plants: Seawater chloride environment — 316L body + SS316 disc + EPDM or HYPALON seat. PN16 rated for reverse osmosis pre-treatment systems.
Vietnam & Thailand HVAC: CF8 (304) body with EPDM seat is the most cost-effective choice for chilled water and condenser water systems in commercial buildings.
Not sure which size or pressure rating you need? Send us your flow rate, pipe size and medium.
Get Free Sizing Report →Wafer vs Lugged vs Flanged Butterfly Valve
| Feature | Wafer | Lugged | Flanged |
|---|---|---|---|
| Connection | Fits between two flanges, through-bolted | Has threaded lugs, can be installed with bolts only on one side | Has its own flanges, bolts directly to mating flanges |
| Weight | Lightest | Medium | Heaviest |
| Face-to-face length | Shortest (EN 558 Series 20) | Same as wafer | Longest |
| Line size isolation | Cannot isolate a single section without shutting down both sides | Can isolate one side (double block capability) | Can isolate independently |
| Cost (DN300) | Lowest | ~15–20% higher than wafer | ~40–60% higher than wafer |
| Best for | HVAC, water treatment, large diameter lines | Pumping stations, risers, maintenance isolation | High pressure, critical process, chemical |
| Our product | Wafer Butterfly Valve | On request | Flanged Butterfly Valve |
Technical Specifications
| Size Range | DN40 – DN600 (NPS 1½” – 24″) |
| End Connection | Wafer type, fits between DIN EN 1092-1 PN10/PN16 / ANSI B16.5 Class 150 / JIS 10K flanges |
| Body Material | CF8M (316) / CF8 (304) — standard; WCB / GGG50 / GG25 available on request |
| Disc | SS304 / SS316 (optional Nylon or EPDM coated) |
| Stem | SS416 / SS304 |
| Seat | EPDM / NBR / Viton (FKM) / PTFE |
| Pressure Rating | PN10 – PN16 / ANSI 150# |
| Temperature Range | -10°C ~ +110°C (EPDM) / -20°C ~ +80°C (NBR) / -20°C ~ +180°C (Viton) |
| Actuation | Lever (DN40–DN200) / Gear (DN250–DN600) |
| Applicable Media | Water, seawater, oil, gas, HVAC, water treatment, fire protection, mild chemicals |
| Testing | shell & seat pressure test per API 609 / EN 593; bubble-tight acceptance per API 598 |
| Material Certificates | EN 10204 3.1 MTC per heat, included with shipment |
| Standard | API 609, EN 593, ISO 5752, face-to-face per EN 558 Series 20 (short wafer pattern) |
Dimension Table — EN 558 Series 20 Wafer (mm)
L = face-to-face length (short wafer pattern). ΦD = matching bolt circle of DIN EN 1092-1 PN16 pipe flanges. n-Φd = through-bolt holes. ANSI B16.5 Class 150 / JIS 10K drilling available on request.
| DN | NPS | L (mm) | H (mm) | H1 (mm) | ISO Top Flange | Mating PN16 ΦD (mm) | Mating PN16 n-Φd |
|---|---|---|---|---|---|---|---|
| 40 | 1½” | 33 | 126 | 70 | F04 | 110 | 4-Φ19 |
| 50 | 2″ | 43 | 126 | 70 | F05 | 125 | 4-Φ19 |
| 65 | 2½” | 46 | 137 | 77 | F05 | 145 | 4-Φ19 |
| 80 | 3″ | 49 | 143 | 92 | F05 | 160 | 8-Φ19 |
| 100 | 4″ | 52 | 164 | 105 | F07 | 180 | 8-Φ19 |
| 125 | 5″ | 56 | 177 | 120 | F07 | 210 | 8-Φ18 |
| 150 | 6″ | 56 | 198 | 134 | F07 | 240 | 8-Φ23 |
| 200 | 8″ | 60 | 231 | 171 | F10 | 295 | 12-Φ23 |
| 250 | 10″ | 68 | 261 | 204 | F12 | 355 | 12-Φ27 |
| 300 | 12″ | 76 | 295 | 241 | F14 | 410 | 12-Φ27 |
| 350 | 14″ | 89 | 355 | 271 | F14 | 470 | 16-Φ27 |
| 400 | 16″ | 102 | 366 | 298 | F16 | 525 | 16-Φ30 |
| 450 | 18″ | 114 | 401 | 331 | F16 | 585 | 20-Φ33 |
| 500 | 20″ | 127 | 438 | 369 | F16 | 650 | 20-Φ33 |
| 600 | 24″ | 154 | 568 | 450 | F30 | 770 | 20-Φ36 |
H and H1 are reference dimensions (stem height and handwheel clearance) — actual values depend on operator and gearbox. Top flange per ISO 5211 for mounting pneumatic/electric actuators.
🧮 Worked Example: Selecting a DN100 Wafer Butterfly Valve
Project: Chilled water system for a shopping mall in Riyadh, Saudi Arabia.
Given: Flow rate Q = 120 m³/h, water temperature = 8°C, pipe size = DN100 (4″), pressure = 6 bar.
Step 1 — Calculate velocity:
Pipe area A = π × (0.1/2)² = 0.00785 m²
Velocity v = Q / (3600 × A) = 120 / (3600 × 0.00785) = 4.24 m/s
Step 2 — Check recommended velocity:
For chilled water, recommended velocity is 1.5–3.0 m/s. Our calculated 4.24 m/s is too high. We either increase pipe size to DN125 (v = 2.72 m/s ) or accept the pressure drop penalty.
Step 3 — Select valve:
DN125 wafer butterfly valve, CF8 (304) body, EPDM seat, PN16, lever operated. Cv ≈ 420 (fully open), pressure drop at 120 m³/h ≈ 0.08 bar — negligible. Mating flanges: DIN EN 1092-1 PN16, K=210 mm, 8×Φ18 bolt holes.
Step 4 — Confirm material:
Riyadh tap water is mild; CF8 (304) is sufficient. If this were a desalination plant with seawater, we would specify CF8M (316) with Viton seat.
⚠️ 4 Common Mistakes When Selecting Wafer Butterfly Valves
Mistake 1 — Using EPDM seat for hot oil or steam: EPDM max temp is +110°C. For hot water above 95°C or thermal oil, use Viton (FKM) or PTFE lined disc.
Mistake 2 — Specifying cast iron body for seawater: Cast iron corrodes in chloride environments. Always use CF8M (316) body + SS316 disc for seawater, desalination or coastal palm oil mills.
Mistake 3 — Oversizing the valve for control service: A butterfly valve has poor control below 20° opening. If you need precise flow regulation, size the valve one size smaller than the pipe, or use a globe valve for throttling.
Mistake 4 — Forgetting actuator torque on large sizes: DN250 and above must use gear operator, not lever. Pneumatic actuators require torque calculation at 8 bar supply pressure — we provide this sizing table on request.
Need Sizing Help or a Quote?
Send size (DN), pressure (PN/ANSI), material (304/316L), seat (EPDM/Viton) and quantity — we reply within 24 hours.
Get Free Quote »Applications
HVAC Systems: Chilled water, hot water and condenser water circuits in commercial buildings.
Water Treatment: Treatment plants, pump stations, distribution networks, RO desalination.
Industrial Piping: Chemical processing, power plants, mining, pulp & paper.
Fire Protection: Fire pump headers and sprinkler system main line control.
Quality Control
1. Raw material inspection (spectrometer test for chemical composition)
2. CNC machining & dimensional inspection
3. Shell pressure test (1.5× PN rating, 60 seconds hold)
4. Seat pressure test (1.1× PN rating, bubble-tight acceptance per API 598)
5. Final visual inspection, torque test & packing
📋 Commercial Terms
Payment: T/T 30% deposit + 70% before shipment; L/C at sight accepted for EPC package orders (MOQ USD 30,000+). PayPal for sample orders.
Warranty: 12 months after shipment for material and manufacturing defects — covers casting defects, disc / seat non-conformance, stem leakage and body dimensional non-conformance (face-to-face, flange drilling). Damage from misuse, improper seat material selection for the rated medium, abrasive solids beyond specified clean-water range, or field disassembly / re-packing by the customer is not covered. Always quote the valve serial number and heat number from the EN 10204 3.1 MTC when raising a claim.
Packaging: Export plywood case; fumigation-free pallet; flange faces and stem protected; disc held closed with transit clip.
Shipping Documents: EN 10204 3.1 MTC per heat, API 609 / API 598 hydro & seat test report, packing list, commercial invoice, EN 10204 3.1 MTC on request.
Shipment Port: FOB Ningbo / Shanghai, China; EXW, CIF or DAP available on request.
Third-Party Inspection: SGS / Bureau Veritas / Intertek pre-shipment dimensional, hydro and seat test inspection supported at buyer cost. Factory audit or video inspection available on request.
FAQ
What is the difference between wafer and flanged butterfly valves?
Wafer type is thinner and lighter, fits between two flanges. Flanged type has its own flanges and bolts directly, easier to install and remove but heavier and more expensive (~40–60% higher at DN300).
What pressure rating is available for wafer butterfly valves?
Standard PN10 / PN16 / ANSI 150#. Higher pressure ratings (PN25, ANSI 300#) are available on request for industrial and power plant service.
Can you supply 316 stainless steel wafer butterfly valves for seawater?
Yes, CF8M (316) body with SS316 disc and EPDM or Viton seat is recommended for seawater and desalination applications. We also supply matching lift check valves and stainless steel pipe for complete seawater systems.
What is the lead time for wafer butterfly valves?
Standard sizes in stock ship within 7–20 days. Custom or large sizes (DN400+) take 25–35 days depending on quantity. Rush orders can be arranged for urgent EPC projects.
Do you provide material certificates and pressure test reports?
Yes, EN 10204 3.1 MTC (material test reports), pressure test certificates and third-party inspection (SGS / Bureau Veritas) are available upon request for every order. We ship EXW, FOB Ningbo/Shanghai, or CIF to your nearest port.
What is your MOQ?
MOQ is 1 piece. We support sample orders for new customers to test quality before bulk orders. For EPC projects, we can schedule production to your delivery timeline.
Can you arrange pre-shipment inspection (PSI)?
Yes. We support SGS, Bureau Veritas or Intertek pre-shipment inspection at the buyer’s cost. Our factory is open for audit or video inspection on request.
Can you supply pneumatic or electric actuated wafer butterfly valves?
Yes. We offer pneumatic actuated and electric actuated versions for automated HVAC and process control systems. Actuator brands available: Air Torque, KITZ, or OEM.
What is your warranty period?
We provide a 12-month warranty after shipment for material and manufacturing defects. This covers casting defects, disc / seat non-conformance, stem leakage and body dimensional non-conformance. Damage from misuse, improper seat material selection for the rated medium, abrasive solids beyond the specified clean-water range, or field disassembly by the customer is not covered. Always quote the valve serial number and heat number from the EN 10204 3.1 MTC when raising a warranty claim.
📚 Further reading:
• Gate Valve vs Globe Valve: Which to Choose?
• Y-Strainers for Pumps & Control Valves
• PN vs Class Pressure Rating: Quick Reference
You May Also Need
Related Technical Guides
Wafer Butterfly Valve Selection Guide · What Is a Wafer Butterfly Valve? · Wafer vs Flanged Butterfly Valve
Request a Quote for This Wafer Butterfly Valve
Tell us the size, pressure and quantity you need. We reply within one working day.
Need a Custom Valve or Fitting?
Send us your specs: pressure, size, material and quantity — our engineers will reply within 24 hours with a detailed quotation. MOQ 1 piece.
FOB Ningbo / Shanghai · 5–10 days to Southeast Asia · 15–20 days to the Middle East · We reply within 24 hours (usually same business day)
Commercial terms: T/T 30% deposit + 70% before shipment, L/C at sight · export plywood case / fumigation-free pallet · 12 months warranty after shipment for material and manufacturing defects · EN 10204 3.1 MTC + API 598 test report + packing list + commercial invoice with every order · SGS / Bureau Veritas / Intertek pre-shipment inspection available
Get Free Quote »
