Wafer Single Plate Check Valve | Chuanglan Valve

▲

Single Plate Check Valve | Wafer Tilting

Low-cost backflow prevention for water and wastewater lines.

Ultra-short 18–180 mm wafer tilting disc check valve, DN40–DN700, PN10/PN16 / ANSI 150# — the shortest check valve in our range

OEM/ODMCustom Manufacturing
ISO 9001:2015Quality Management
Established 2009Valve Manufacturing
7–15 DaysLead Time

* Standard lead time depends on order quantity and destination country. 5–10 days to Southeast Asia, 15–20 days to the Middle East.

✍️ Reviewed by Chuanglan Valve Engineering Team · Last updated Oct 2026 · Follow us on LinkedIn
Wafer single plate check valve, stainless steel

A wafer single plate check valve (also called tilting disc check valve) is the shortest check valve in our range — an ultra-compact, spring-assisted check valve that prevents backflow on HVAC chilled/condenser water circuits, cooling towers, pump stations and industrial piping. Its single tilting disc swings open under forward flow and snaps shut on reverse flow, minimizing water hammer.

Chuanglan manufactures wafer single plate check valves in CF8M (316) and CF8 (304) stainless steel as premium range. Ductile iron (GGG50) and cast iron (GG25) are standard for HVAC / water service. Sizes DN40–DN700 (NPS 1½″–28″), wafer body fits between DIN EN 1092-1 PN10/PN16 / ANSI B16.5 Class 150 / JIS 10K flanges. For tighter shutoff on large lines, compare our dual plate check valve; for steam and boiler feed, see lift check valve.

The key advantage of a single plate check valve is its ultra-compact body. Face-to-face is only 18–180 mm depending on size, compared to 16–75 mm for dual-plate wafer check valves and 150–1350 mm for flanged swing check valves. This makes it the ideal choice when you are retrofitting an existing pipeline where space is extremely tight — AHU plant rooms, ceiling voids, skid-mounted pump packages and equipment connections. We directly serve EPC contractors and valve distributors in Southeast Asia (Indonesia, Malaysia, Thailand, Vietnam) and the Middle East (Saudi Arabia, UAE, Qatar, Kuwait).

When selecting a single plate check valve, consider: size (DN40–DN700), pressure rating (PN10 / PN16 / ANSI 150#), body material (cast iron for water/HVAC, ductile iron for general, WCB for oil/gas, CF8M for corrosive service), seat material (NBR up to +80°C, EPDM up to +120°C for chilled water/HVAC, Viton up to +200°C for chemical/oil), spring stiffness (standard / low-cracking / anti-chatter), and flow direction. Always install a Y-strainer upstream to protect the tilting disc from welding slag and scale.

Southeast Asia & Middle East Market Notes

Thailand / Vietnam hotels, malls & hospitals HVAC: Ductile iron GGG50 body, EPDM seat, wafer single plate — standard for chilled water and condenser water circuits. The 18–55 mm face-to-face fits existing AHU and cooling tower connections during retrofits without changing pipe length.

Indonesia / Malaysia data centers & semiconductor fabs: Ductile iron body, NBR/EPDM seat, PN16 — used on chilled water primary/secondary pumps, CRAH connections and cooling return lines. Compact body fits in skid-mounted pump packages.

Saudi Arabia / UAE desalination & HVAC for high-rise towers: CF8M body, SS316 disc, Viton seat, ANSI 150# — used on SWRO brine return, cooling tower circulation and domestic water. Corrosion-resistant for coastal chloride environments.

Not sure whether single plate, dual-plate or swing check fits your line? Send us your pump flow rate, line size and available space.

Get Free Sizing Report →

Single Plate vs Dual-Plate vs Swing vs Lift Check Valve

FeatureSingle Plate (This)Dual-Plate / ButterflySwingLift
Face-to-face18–180 mm (shortest)16–75 mm (wafer)150–1350 mm130–750 mm
Closure speedVery fast<50 ms (fastest)Slow (slam risk)Medium
Pressure dropLowestLowLowestHighest
Shutoff tightnessGoodBetterGoodBest (metal/soft)
Handles solidsNoLimitedYesNo (guides jam)
OrientationAnyAnyHorizontal onlyHorizontal only
Best size rangeDN40–DN200DN40–DN700DN50–DN600+DN15–DN300
Best forHVAC retrofits, tight skids, AHU connectionsCooling water, pump discharge, water hammerLarge water, wastewater, slurrySteam, boiler feed, high-pressure oil

Technical Specifications

TypeWafer single plate / Tilting disc check
Size RangeDN40 – DN700 (NPS 1½” – 28″)
End ConnectionWafer type, fits between DIN EN 1092-1 PN10/PN16 / ANSI B16.5 Class 150 / JIS 10K flanges
Body MaterialCF8M (316) / CF8 (304) — premium; WCB / GGG50 / GG25 on request
DiscSS304 / SS316 tilting disc, NBR / EPDM / Viton soft seat
SpringSS304 / SS316 stainless steel
Pressure RatingPN10 / PN16 / ANSI Class 150
Temperature Range-10°C ~ +120°C (NBR) / -20°C ~ +120°C (EPDM) / up to +200°C (Viton)
Face-to-Face18–180 mm (shortest in check valve family)
InstallationHorizontal, vertical (up or down) or inclined
Applicable MediaWater, cooling water, HVAC, oil, gas, pump discharge lines
Testingshell & seat pressure test per API 594
Material CertificatesEN 10204 3.1 MTC (material test reports) included
StandardAPI 594, EN 558, ISO 5752

Dimension Table — Wafer Single Plate PN16 (mm)

DNL (Face-to-Face)D (OD)D1 (Bolt Circle)D2 (Disc)H (Height)
4018110886730
50201251027635
65241451228640
802616013810045
1003218015811650
1253821018814560
1504224021217070
2005529526822690
25065355320280110
30075410370325130
35085470430365150
40095525480410170
500127650580520210
600150770680630250
700180895800740290

* PN10 drilled pattern available on request. ANSI Class 150 / JIS 10K flange drilling also available.

Worked Example: Replacing an Old Swing Check Valve on a DN80 Condenser Water Pump in Bangkok

Project: Retrofit of a 30-year-old office building in Bangkok, Thailand. DN80 condenser water pump discharge to cooling tower.
Problem: The existing flanged swing check valve (face-to-face 280 mm) is leaking and slamming on every pump trip. No room to expand the pipe — the pump skid is bolted to the floor, and 280 mm is already the maximum allowed between pump flange and tower header.

Step 1 — Confirm space available:
After removing the old swing check, the flange gap is still ~280 mm. A new flanged swing check would fit, but it slams. A wafer single plate DN80 has L = 26 mm — it fits easily, leaving 254 mm of pipe to re-use. No pipe cutting needed.

Step 2 — Confirm pump conditions:
Q = 80 m³/h, DN80 pipe. Velocity v = 80 / (3600 × 0.00503) = 4.4 m/s — a bit high for condenser water (target 2–3 m/s) but acceptable for a retrofit without changing pumps. Reverse flow on pump trip will slam a slow swing check; the spring-assisted single plate closes in ~0.1 s, preventing water hammer.

Step 3 — Material & seat:
Condenser water at 32–38°C, non-corrosive. Specify ductile iron GGG50 body, EPDM seat (best for cooling water up to +120°C, handles mild water treatment chemicals). No need for CF8M on budget retrofit.

Step 4 — Installation:
DIN EN 1092-1 PN16 flanges (D=200 mm, K=160 mm, 8×Φ18 bolt holes). Install wafer between the existing flanges using longer through-bolts. Add a Y-strainer upstream to catch rust scale from old pipework. Spring-loaded disc closes in any orientation — install horizontal.

4 Common Mistakes When Selecting Wafer Single Plate Check Valves

Mistake 1 — Using it on dirty water or sewage: The single tilting disc wedges open on rags, leaves or particulates, causing permanent leakage. For wastewater / palm oil effluent, choose a swing check valve — its disc swings fully out of the flow path.

Mistake 2 — Ignoring flow direction arrow: Every wafer check has a cast flow arrow. Installing backwards blocks the line — the disc can’t open. Verify arrow before tightening flange bolts.

Mistake 3 — Under-sizing for low flow: If minimum flow velocity is below 0.5 m/s, the spring may not fully open the disc, causing pressure drop and chatter. Tell us your minimum pump flow so we can fit a softer spring.

Mistake 4 — Forgetting a Y-strainer: Welding slag, Teflon tape and pipe scale score the soft seat. Always install a Y-strainer upstream — it costs 1/10 of the valve and doubles seat life.

Need Sizing Help or a Quote?

Send size (DN), pressure (PN/ANSI), material (304/316L), seat (EPDM/Viton) and quantity — we reply within 24 hours.

Get Free Quote »

Applications

HVAC & Cooling: Chilled water, condenser water, cooling tower circulation, AHU connections.
Data Centers: CRAH unit return, primary/secondary chilled water pumps, skid packages.
Water & Wastewater: Building domestic water, fire water mains (clean service only).
Oil & Chemical: Hydraulic oil, cooling oil circuits (NBR / Viton seat).

Commercial Terms & Shipping

Payment: T/T 30% deposit + 70% before shipment; L/C at sight accepted for orders above USD 20,000. PayPal for sample orders.

Warranty: 12 months after shipment for material and manufacturing defects. Covers casting defects, seal leakage and material non-conformance. Damage from misuse, improper installation or corrosion beyond specified limits is not covered.

Packaging: Export plywood case (fumigation-free) or seaworthy pallet. Suitable for FCL container and LCL consolidation.

Shipping Documents: EN 10204 3.1 MTC, pressure test certificate, packing list, commercial invoice. Certificate of origin and BL available on request.

Shipment Port: FOB Ningbo / Shanghai, China. Can also arrange CIF / DAP to your destination port.

Third-Party Inspection: SGS, Bureau Veritas or Intertek pre-shipment inspection supported at your cost.

FAQ

Single plate vs dual plate wafer check valve — which should I pick?

Single plate (tilting disc) has the shortest face-to-face (18–180 mm) and lowest pressure drop, ideal for space-constrained HVAC and pump discharge. Dual plate gives tighter shutoff and handles higher reverse pressure, better for large lines (DN300+) and water hammer protection. For DN40–DN200 single plate is the common choice; DN250+ we usually recommend dual plate.

Why is the body so short — can it still handle pressure?

Yes. The short body is a wafer pattern clamped between two standard flanges — the flange bolts carry the line pressure, not the valve body itself. Pressure rating is PN16 / ANSI 150# just like a full flanged valve; only the face-to-face length is reduced.

Does it work on vertical pipe (flow going up)?

Yes. The spring-assisted disc closes mechanically, independent of gravity. Single plate wafer check valves work in horizontal, vertical-up, vertical-down and inclined orientations — a key advantage over flanged swing and lift check valves which require horizontal mounting.

Can it handle sewage or wastewater with solids?

We do not recommend it for wastewater with solids, rags or fibers — the tilting disc can wedge open on debris. For sewage, choose a flanged swing check valve. Clean water, HVAC cooling water, oil and gas are fine.

What cracking pressure should I expect?

Standard spring cracking pressure is ~0.05–0.1 bar (0.7–1.5 psi). For very low flow systems we can fit a softer spring; for high-vibration applications a stiffer spring prevents chattering. Tell us your minimum flow velocity.

What is the difference between this and a tilting disc check valve?

They are the same product. “Single plate”, “tilting disc”, “wafer tilting” and “single leaf” are all industry names for the same wafer-pattern check valve with one hinged disc. Some manufacturers call it “wafer tilting disc”, others “single plate”.

MOQ, stock and delivery time?

MOQ is 1 piece. DN40–DN200 in cast iron / ductile iron are usually in stock (7 days). DN250 and above, WCB carbon steel or CF8M stainless takes 15–30 days. ANSI 150# / JIS 10K flange drilling available on request.

What is the warranty period for your valves?

We provide a 12-month warranty after shipment for material and manufacturing defects. This covers casting defects, seal leakage and material non-conformance. Damage from misuse, improper installation or corrosion beyond specified limits is not covered.

📚 Further reading:
• Wafer Check Valve vs Swing Check Valve (2026 Guide)
• How to Select a Wafer Butterfly Valve for Seawater Service
• Butterfly Valve Selection Guide (Size, Pressure, Material)

You May Also Need

Request a Quote for This Single Plate Check Valve

Tell us the size, pressure and quantity you need. We reply within one working day.








    Need a Custom Valve or Fitting?

    Send us your specs: pressure, size, material and quantity. Our team will review the requirements and provide a direct quote.

    Southeast Asia: Indonesia, Malaysia, Thailand, Vietnam, Singapore, Philippines · Middle East: Saudi Arabia, UAE, Qatar, Kuwait, Oman, Bahrain · Other: the Americas, Europe, Africa, Australia

    FOB Ningbo / Shanghai · We usually reply within 24 business hours.

    Commercial terms: T/T 30% deposit + 70% before shipment, L/C at sight may be considered · export plywood case · 12 months warranty after shipment · EN 10204 3.1 MTC available on request · third-party inspection can be arranged on request.

    Disclaimer: This guide is for general engineering reference only. Final valve selection, sizing and installation must follow the manufacturer data sheet, the project P&ID and the applicable code (EN 1092, ASME B16.5, ASME B16.34, EN 10204 3.1). Where this article and those documents differ, the documents govern.